DNR-Pro.org is not affiliated with any government agency
Welcome Guest Search | Active Topics | Members | Log In | Register

Fly Fishing Tips and Techniques Options
tmac187
Posted: Tuesday, May 27, 2008 10:45:17 AM

Rank: Administration
Groups: Administration

Joined: 12/10/2007
Posts: 128
Let's see what everybody's favorite fly fishing tip or technique is. Post them here!

If it's April and the insects are just beginning to spawn, then try using a fly that mimics larvae. If it's late in the season then use a dry fly. Fish will see this as normal and won't be so hesitant to bite.

Now let's here your's...Cool
Sponsor
Posted: Tuesday, May 27, 2008 10:45:17 AM

Pro Bass Fishing Techniques Exposed!!
Plus Get Over $400.00 In Extreme Largemouth Bass Angling Software Absolutely FREE....

Get Your Federal Firearms License 2008
New 2008 Federal Firearms Kit To Help You Get Your Federal Firearms License And Buy Guns Wholesale.

* Login or Register to remove these ads

Vannahban
Posted: Tuesday, May 27, 2008 11:48:25 AM
Rank: Advanced Member
Groups: Member

Joined: 4/1/2008
Posts: 36
Here's a casting tip I use religiously. Take a small hand towel with you next time you go fly fishing. When your done fishing, make one last long cast to wet the fly line, then clean the line with your towel while your reeling in. This helps my line to cast smoothly next time I go fishing by cleaning the line and removing any dirt or deposits.
hunting1979
Posted: Tuesday, May 27, 2008 12:18:41 PM

Rank: Advanced Member
Groups: Member

Joined: 4/29/2008
Posts: 60
Location: Iowa
I have found the mosquito fly pattern to be very effective in catching trout and other types of fish.


marvelousC
Posted: Monday, June 30, 2008 11:35:40 AM

Rank: Member
Groups: Member

Joined: 3/17/2008
Posts: 27
Location: Mass
Do not start your overhead cast with a pile of slack at your feet, or with your fly rod tip more than 6" above the water. The fly rod won't load until the fly line becomes tight to the rod, so this is impossible if your fly line is in a pile at your feet. Instead, roll cast the fly line out straight and then make the cast.

With your line out fairly straight and your fly rod tip at the water, you'll notice that the rod tip starts to load (bend) almost immediately when you initiate the cast. Because of the surface tension of the water, the line resists the lifting of the fly rod and starts to load it as soon as you move it. If you start that same cast with the fly rod tip four feet above the water, you just lost four feet of free energy and the cast becomes much more difficult to complete. Start and finish your cast with the fly rod tip at the water. Use this fly casting technique and make the fly rod do the work so you don't have to.
hunting1979
Posted: Thursday, July 17, 2008 8:41:53 AM

Rank: Advanced Member
Groups: Member

Joined: 4/29/2008
Posts: 60
Location: Iowa
Always lubricate your knot

If you break off a fly and the end of your line comes back in a curlicue, your knot didn't reach its maximum breaking strength. Odds are you seated the knot without lubricating it. Never attempt to draw your knots up dry. They will rarely, if ever, seat correctly and will slip and fail before reaching their maximum breaking strength.

To stop this from happening, form the knot by tightening it up just enough to keep it from unraveling on its own, and then lubricate the knot with a little saliva or by dipping it into the water before the final tightening. Then wrap the line around your fingers a couple of times and pull until you feel the fly line stop stretching.
Users browsing this topic
Guest


Forum Jump
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.

Main Forum RSS : RSS

FlatEarth Theme Created by Jaben Cargman (Tiny Gecko)
Powered by Yet Another Forum.net version 1.9.1.8 (NET v2.0) - 3/29/2008
Copyright © 2003-2008 Yet Another Forum.net. All rights reserved.
This page was generated in 0.202 seconds.